Where to mount a Cobra 29?

buterbn · 12-10-2006, 07:34 PM

Hey fellas,
I know the subject of where to mount cb's has been talked about in great length. However, through all my searching, I could not find a cobra 29 or other cb of equivalent size that wasn't mounted up above. I am thinking of going back to my old mount that i had on the roll bars, but wanted to see any pics of it elsewhere. Specifically, does this cb fit on the quadratec mount which mounts next to the 4wd shifter? I wanted to mount it below my seat but I dont think I would be able to lean it forward, am I wrong? I am basically looking to mount it low and out of the way. Would also like to see how yu made your mount accros the roll bar? I used a long L track thing but am looking for something cleaner.. Thanks a lot guys in advance.

Jason

buterbn · 12-10-2006, 08:21 PM

Any ideas?

ehirner · 12-10-2006, 08:26 PM

Try having a bit more patience than about 50 minutes.

ABQ-TJ · 12-10-2006, 09:07 PM

I mounted a cobra on the back of my center console for a bit

TJ Rat · 12-10-2006, 10:02 PM

I mounted my Cobra 29 above the rear view mirror. $19.00 in materials. Send me your email and I will send you a couple of pics.

Tink · 12-11-2006, 01:08 AM

My 29 is mounted on a piece of 3/4 alu. angle that stretches across the rollcage bars. It is high enough not to block my rear view and it is close by to reach. After running the wires in the v of the angle I covered the whole thing in 1 inch ID pipe insulation to dress it up some. Most people think it is part of the original cage.

12-10-2006, 07:34 PM	#1
buterbn Registered Join Date: Jun 2004 Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts	Where to mount a Cobra 29? Hey fellas, I know the subject of where to mount cb's has been talked about in great length. However, through all my searching, I could not find a cobra 29 or other cb of equivalent size that wasn't mounted up above. I am thinking of going back to my old mount that i had on the roll bars, but wanted to see any pics of it elsewhere. Specifically, does this cb fit on the quadratec mount which mounts next to the 4wd shifter? I wanted to mount it below my seat but I dont think I would be able to lean it forward, am I wrong? I am basically looking to mount it low and out of the way. Would also like to see how yu made your mount accros the roll bar? I used a long L track thing but am looking for something cleaner.. Thanks a lot guys in advance. Jason

12-10-2006, 08:26 PM	#3
ehirner Forum Leader Join Date: Jul 2001 Location: Eastern PA Posts: 15,632 Thanks: 0 Thanked 30 Times in 30 Posts	Try having a bit more patience than about 50 minutes. __________________ 09 F-150 SC · 06 Roadliner

12-10-2006, 09:07 PM	#4
ABQ-TJ Registered Join Date: Jan 2002 Location: Albuquerque, NM Posts: 4,984 Thanks: 5 Thanked 3 Times in 2 Posts	I mounted a cobra on the back of my center console for a bit __________________ www.nmoffroad.com

12-10-2006, 10:02 PM	#5
TJ Rat Registered Join Date: Dec 2001 Location: Houston, TX Posts: 721 Thanks: 0 Thanked 1 Time in 1 Post	I mounted my Cobra 29 above the rear view mirror. $19.00 in materials. Send me your email and I will send you a couple of pics. __________________ Semper Fi

12-11-2006, 01:08 AM	#6
Tink Registered Join Date: Nov 2003 Location: Summerville ga. Posts: 787 Thanks: 5 Thanked 2 Times in 1 Post	My 29 is mounted on a piece of 3/4 alu. angle that stretches across the rollcage bars. It is high enough not to block my rear view and it is close by to reach. After running the wires in the v of the angle I covered the whole thing in 1 inch ID pipe insulation to dress it up some. Most people think it is part of the original cage. __________________ :nuts:

12-10-2006, 08:21 PM	#2
buterbn Registered Join Date: Jun 2004 Posts: 2 Thanks: 0 Thanked 0 Times in 0 Posts	Any ideas?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode